M-BLOC® Type X Gypsum Board End Tape

M-BLOC® Type X Gypsum Board


M-BLOC® Type X Gypsum Board

M-Bloc® Type X interior gypsum panels treated with AzoTech™ fungicide were developed as an improved moisture resistant wallboard, with added mold resistance in the core and paper. M-Bloc® Type X interior gypsum panels consist of a fire, mold and moisture resistant core encased in 100%recycled paper. Additionally the core has been reinforced with fibers, increasing its strength and providing fire resistance ratings when used in tested assemblies.

At an independent laboratory, certified in accordance with ISO 17025-2005, M-Bloc panels have been tested to the industry’s most rigorous standards achieving the best results possible. Per ASTM G 21 the panels attained a 0 and ASTM D 3273 scored a perfect 10, thus minimizing the risk of mold and mildew growth.

Basic Uses

M-Bloc Type X interior gypsum panels are a lightweight cost efficient interior wall or ceiling panel for use in new construction or renovation work. M-Bloc panels can be used throughout a project as well as the adhesive application of ceramic or plastic tile in limited wet areas, e.g., bathrooms, kitchens, laundry, and utility rooms. M-Bloc Type X panels can be finished the same as regular gypsum wallboard and they accept a wide variety of attractive finishes.


M-BLOC Type X gypsum wallboard has attained the GREENGUARD Indoor Air Quality Certified status and GREENGUARD Children & Schools Indoor Air Quality Certified status. For more information select the link at right.

Product Data


Thickness Widths Lengths Edge Type
5/8" (15.9mm) 4' (1219mm) 8' - 12' (2438mm - 3658mm) Tapered

Technical Data

Storage & Handling

Gypsum board does not generate or support the growth of mold when it is properly transported, stored, handled, installed, and maintained. However, mold spores are present everywhere and when conditions are favorable; mold can grow on practically any surface. GYPSUM BOARD MUST BE KEPT DRY to prevent the growth of mold. Adequate ventilation shall be provided to prevent condensation.

Gypsum board that has visible mold growth must not be used. For additional information refer to Gypsum Association publication, “Guidelines for the Prevention of Mold Growth on Gypsum Wallboard” (GA-238).

Gypsum board must be stored in an area that protects it from adverse weather conditions, condensation, and other forms of moisture. Job site conditions that can expose gypsum board to water or moisture must be avoided.

Gypsum board must be protected during transit with a weather-tight cover in good condition. Plastic shipping bags are intended to provide protection during transit only and must be promptly removed upon arrival of the load. Failure to remove the shipping bag can increase the likelihood of developing conditions favorable to the growth of mold.

Gypsum board must be delivered to the job site as near to the time it will be used as possible. Individuals delivering gypsum board to jobsites should ensure that it is carried, not dragged, to place of storage/installation to prevent damage to finished edges.

Applicable Standards

Mold Resistance Score of 0 (ASTM G 21)
Score of 10 (ASTM D 3273)
Water Absorption <5% (ASTM 1396)
Manufacturing ASTM C 1396 section 7 (C 630)
Federal Specification - SS-L-30D Type III and Type VII, Grade X
Installation ASTM C 840
Gypsum Association GA-216
Gypsum Association GA-214
Surface Burning Characteristics ASTM E 84
Flame Spread 15
Smoke Developed 0

Fire Resistance Ratings

LEED / Green

LEED Contributions

Our products can contribute to the following credits within the Materials and Resources (MR) category.

  • LEED MR Credit 2: Construction Waste Management
  • LEED MR Credit 4: Recycled Content
  • LEED MR Credit 5: Regional Materials

Our products can contribute to the following credit within the Indoor Environmental Quality (IEQ) category.

  • LEED IEQ Credit 4.6: Low-Emitting Materials - Ceiling and Wall Systems (SCHOOLS ONLY)

To learn more please click the LEED link at right.